What is the difference between the full cover hinge and the half cover and side cover hinge? What are the hinges?

What are the differences and differences between full-cover hinges, half-cover hinges, and side-opening hinges? What are the types of hinges? What I recommend for you today is the knowledge of these aspects. From this, you can learn, first of all, It can be seen from their structural design that the so-called full cover may be more suitable for some special places, while other hinges are not the same. Another aspect and can also be classified according to the material, which can be classified according to the size and size. The detailed division includes some aluminum alloy steel materials, which are waterproof, moisture-proof and corrosion-resistant, and have a longer service life. There may also be other plastic hinges. They are relatively more cost-effective, and you can learn about them through the following.

the
1. What is the difference between full cover hinges and half cover and side cover hinges?

There are three types of door hinges: 45, 180, and 270. The angle indicates the inner angle after the cabinet is opened.

The full cover, half cover, and inlay of the hinge are determined according to the side panel of the cabinet, and the thickness of the side panel is generally 16-18MM.

Full cover: The door completely covers the side panel of the cabinet, and there is a gap between the two so that the door can be opened safely. Straight arm (0 mm) full cover door Straight arm (0 mm)

Half cover: In this case, two doors share a side panel. There is a minimum total gap required between them. The distance covered by each door is reduced accordingly, requiring the use of door hinges with curved arms. Middle curved (9.5mm) half cover door curved (9.5mm)

Responding door: In this case the door is inside the cabinet, next to the side panel of the cabinet. It also needs a clearance so that the door can be opened safely. Requires a hinge with a very curved hinge arm. Daqu (16 mm) semi-recessed Daqu (16mm)

the
the
2. Types of hinges

Ordinary hinges: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After the hinges are installed, various touch beads must be installed. , otherwise the wind will blow the door panel.

Pipe hinge: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height of the plate up and down, left and right , Thickness. One of its characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127 degrees, 144 degrees, 165 degrees, etc. have corresponding hinges to match, so that various cabinet doors can be stretched accordingly. Spend.

Door hinge: It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, copper bearing hinges are mostly used. Because of its beautiful and bright style, moderate price, and equipped with screws.

Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible, and it is mostly used on heavy-duty doors or special steel frame steel doors.

Inclined release hinge: This kind of hinge makes use of the inclined plane of the hinge and the weight of the door leaf to automatically close the door. It is mainly suitable for lighter wooden doors or half-section doors such as toilets.

The above recommendation is about the comparison between various hinges and the evaluation of the types. From this, we can know that the common hinges include full cover hinges, half cover hinges and side cover hinges. Three There are certain differences in their respective designs. In addition, suitable and reasonable hinges may be waterproof and moisture-proof stainless steel frame materials, or plastic materials. The corresponding cost performance and advantages are not the same. Suitable places There are also big differences. We should combine our actual needs and our respective budgets for reference, so as to achieve satisfactory results and ultimate goals.

What are the types of hinges? What are the common specifications of hinges?

Hinges are widely used in our lives. I believe that everyone is familiar with the material of hinges. Hinges are items that we will inevitably use when opening and closing doors. Whether it is a security door at home or a solid wood door indoors, Hinges are all required to be installed, but different doors use different types of hinges. Many users and friends only have a superficial understanding of hinges, so today we will explain them in detail in this article. Introduces some information about hinges.

What are the types of hinges?

Ordinary hinges. Mainly used for doors and windows. Ordinary hinge specifications: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After installing the hinge, you must install all kinds of touch beads, otherwise the wind will blow the door panel.

Pipe hinge. It is mainly used for the connection of furniture door panels, also called spring hinge. Pipe hinge specification page: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 1620 mm. The material is galvanized iron , Zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height and thickness of the plate up and down, left and right. One of its characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127-degree, 144-degree , 165 degrees, etc. are matched with corresponding hinges, so that various cabinet doors have corresponding extensions.

Door hinge. It is divided into ordinary type and bearing type. The bearing type is divided into copper and stainless steel. Specifications of door hinge: it is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and copper in terms of material. Quality, stainless steel. Judging from the current consumption situation, more copper bearing hinges are used, because of its beautiful and bright style, moderate price, and equipped with screws.

What are the common specifications of hinges?

There are many types of hinge specifications. The specifications of our commonly used doors and windows are 50.8*30*1, 100*60*1, 63*35*1, 101.6*76.2*2, 88.9*88.9*3, etc. Everyone is choosing When using hinges, pay attention to whether the surface plating of the hinges is fine and smooth, whether the edges of the spring pieces have been polished, and check whether the hinges are relatively light. If they are too heavy, they will not be conducive to rotation. The star-rated hotels are still common residential buildings, and it is difficult for people to see wooden "hukou". Most of the doors and windows of modern buildings use metal door hinges. The modern production of door hinges replaces the ancient "hukou". The ancient invention of "hushu" still remains on some old doors and windows of some ancient buildings and rural residential buildings in Guanzhong.

The above is all the content about the hinge that we introduced to you. In this article, we actually divide the content of the hinge into two parts. First, we introduce the classification of the hinge, because we are in a At the beginning, it was mentioned that different doors may use different hinges, so it is important to know the types of hinges. Then we also analyzed the general specifications of hinges. This part of knowledge is helpful for everyone to buy hinges by themselves. Still a great help.

1. According to the type of base, it can be divided into detachable type and fixed type;

2. According to the type of arm body, it is divided into two types: slide-in type and snap-in type;

3. According to the cover position of the door panel, it is divided into full cover (straight bend, straight arm) with a general cover of 18%, half cover (medium bend, curved arm) with a cover of 9%, and the built-in (large bend, large bend) door panels are all hidden inside.

Hinges are mainly installed on doors and windows, and hinges are more installed on cabinets. According to the classification of materials, they are mainly divided into stainless steel hinges and iron hinges; in order to let people enjoy better, hydraulic hinges (also known as damping hinges) have appeared. Its characteristic is that it brings a buffer function when the cabinet door is closed, which minimizes the noise caused by the collision with the cabinet body when the cabinet door is closed.

Extended information

Notes on hinge use:

1. Wipe gently with a dry soft cloth, do not use chemical cleaners or acidic liquids to clean, if you find black spots on the surface that are difficult to remove, wipe it with a little kerosene;

2. It is a normal phenomenon to make noise after a long time of use. In order to ensure the smooth and quiet pulley for a long time, you can regularly add some lubricating oil for maintenance every 2-3 months.

3. Prevent heavy objects and sharp objects from bumping and scratching.

4. Do not pull or pull hard during transportation, which may damage the hardware at the furniture joints.

Hinge type introduction Classification information description

When it comes to hinges, we all know that it is a basic accessory product, often called a hinge, but the hinges in our impression are generally similar, mainly installed in some cabinet doors and windows or ordinary wood In the door, it can play the role of making it easy for everyone to open and close. But in fact, the hinge can be classified in detail, such as ordinary hinges, pipe hinges or door hinges. In addition to classification according to shape, the field of use The difference in location and location also determines their names. When purchasing, we should refer to the differences between different hinges to understand.

1. Types of hinges

Ordinary hinges: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After the hinges are installed, various touch beads must be installed. , otherwise the wind will blow the door panel.

Pipe hinge: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height of the plate up and down, left and right , Thickness. One of its characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127 degrees, 144 degrees, 165 degrees, etc. have corresponding hinges to match, so that various cabinet doors can be stretched accordingly. Spend.

Door hinge: It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, copper bearing hinges are mostly used. Because of its beautiful and bright style, moderate price, and equipped with screws.

Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible, and it is mostly used on heavy-duty doors or special steel frame steel doors.

Inclined release hinge: This kind of hinge makes use of the inclined plane of the hinge and the weight of the door leaf to automatically close the door. It is mainly suitable for lighter wooden doors or half-section doors such as toilets.

Cold storage door hinge: the surface is baked, the large size is made of steel plate, and the small size is made of cast iron. It is used for cold storage doors or heavy insulation doors.

Fan-shaped hinge: The thickness of the two sheets of the fan-shaped hinge is about half thinner than that of ordinary hinges, and it is suitable for various doors and windows that need to be rotated to open and close.

Silent hinge: also known as nylon washer hinge, when the door and window are opened and closed, the hinge is silent, and it is mainly used on the doors and windows of public buildings.

Single-flag hinge: The hinge is made of stainless steel, which is rust-resistant and wear-resistant, and easy to disassemble. It is mostly used on double-layer windows.

Window hinge: when installing, the two leaf plates with the mandrel should be installed on both sides of the window frame, and the two leaf plates without the mandrel should be installed on both sides of the window sash. One of the negative plates without the mandrel with a groove must be installed on the The grooved side of the window sash is convenient for loading and unloading of the window sash. It is used on the movable windows of factories, warehouses, houses, public buildings, etc.

Multifunctional hinge: when the opening angle is less than 75, it has the function of automatic closing. When it is at an angle of 75-90, it will be stable by itself, and if it is greater than 95, it will be automatically positioned. This hinge can be installed on the door instead of an ordinary hinge use on.

Anti-theft hinge: for ordinary hinges, when the shaft is pulled out, the door leaf can be removed. Anti-theft hinges can prevent the door leaf from being removed through the self-locking effect of the pins and pin holes on the two leaves of the hinge. It plays an anti-theft role and is suitable for residential doors.

Spring hinge: It can make the door leaf close automatically after opening. The single spring hinge can only be opened in one direction, and the double spring hinge can be opened in both directions. It is mainly used on the gate of public buildings.

Biaxial hinge: There are two kinds of biaxial hinges, left and right, which can make the door leaf open, close and disassemble freely. It is suitable for general door and window leaves.

From the above, we can know that there are many types of hinges, and the classification standards are also different, including starting from the purpose and appearance, or starting from the place and field of use, the types and names of hinges corresponding to different classification standards will also have different types. The difference, such as common door hinges, as the name implies, is used on some large doors to help open and close the hinges, that is, the so-called door hinges, and different classifications of hinges can be further detailed according to size and size. We should understand the parameters in this aspect when we study and refer to, and compare and get suitable and reliable suggestions and solutions.

Hinge Encyclopedia brings you the types of hinges

When you decorate a room, you need to use a lot of decoration materials, and you also need a lot of furniture to decorate the whole room, so that the room looks very beautiful. When you install doors and windows, you need to use a kind of object called a hinge. The lotus leaf is placed on the door and window The installation is very important, because the connection between the door and the door needs to be done with a hinge. There are many types of lotus leaves. When you choose, you may not know which one to choose because there are too many types. The following editor is for Let us introduce the types of hinges in detail!

What are the types of hinges?

List of Hinge TypesOrdinary Hinge

It is used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After installing the hinges, various bumpers must be installed, otherwise the wind will Blow the door.

the
List of Hinge TypesPipe Hinges

It is also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height and thickness of the plate up and down, left and right. It One of the characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127-degree, 144-degree, 165-degree, etc. have corresponding hinges to match, so that various cabinet doors have corresponding extensions.

the
List of Hinge Types - Door Hinge

It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, more copper bearing hinges are used because of their beautiful style. , bright, affordable, and equipped with screws.

the
Hinge specification and size:

Length*Width:

2 inches*1.5-1.8 inches

2.5 inches*1.7 inches

3 inches*2 inches

4 inches * 3 inches

5 inches*3-3.5 inches

6 inches*3.5-4

Note: inch means inch, 1 inch=25.4mm

the
Hinge installation method

The installation of the hinge is very simple, but at the same time, it is also necessary to pay attention to the differences in the style, type, and performance of the mother and child hinges. There are also certain differences in the installation. The built-in mother and child hinge is installed. It is necessary to leave a certain gap so that the door can be opened safely and flexibly. The full cover type mother hinge is installed, and the door is completely covered on the surface of the side panel of the cabinet, so it is necessary to pay attention to the size of the gap between the two. The half cover type mother hinge When installing two doors sharing the same side panel, there is a required small gap between the two, and the coverage distance of each door must be reduced accordingly.

I believe that after reading the introduction above, you should know what types of hinges are there? There are many types of lotus leaves. When choosing hinges, you must choose according to the type of your doors and windows. After installing the hinges, if you When there are some quality problems when using doors and windows, or you need to replace the doors and windows, you can remove the hinges and replace them with new doors and windows, which greatly saves the cost of maintenance and replacement. I hope that the editors suggestions can help you choose Appropriate hinges can help you better repair doors and windows.

How about hidden hinges? Types of hinges?

What I recommend for everyone today is the evaluation of hidden hinges and the knowledge of hinge types. From this, we can know that, first of all, common hidden hinges are different from ordinary full cover hinges. Their design It is quite special. If it is installed between the cabinet door and the wooden door, it will not be easy to find later. On the other hand, this hidden hinge also means that we can use it when we stand outside the door and install the lock on the left, or the door lock is installed It can also be used on the right side, so this kind of hinge is more in line with the actual characteristics of humanization, and they are easy to install, suitable for invisible doors, and there are many adjustment directions. You can refer to the following for details. We will explain these few for you. Aspects of evaluation and presentation analysis.

the
1. How about the hidden hinge

1. Beautiful hidden device, without any exposed parts, beautiful and generous! 2. Adjustable three-dimensional adjustable, the adjustment direction is up and down, left and right, and bevel adjustment. 3. The durable hidden hinge is made of imported No. 3 zinc , the service life is as long as 30 years! 4. Easy to install. After the factory has opened the hole and installed it, you only need to take the hexagon wrench to the customer and screw it on. 5. Save after-sales costs. When the door sags, the customer can pass the Manually adjust the hinge to adjust the door, which greatly saves the cost of the manufacturer's door after-sales. Real estate forum, decoration forum, owner forum, P3 V9 O- M3 T"

2. Types of hinges

Ordinary hinges: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After the hinges are installed, various touch beads must be installed. , otherwise the wind will blow the door panel.

Pipe hinge: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height of the plate up and down, left and right , Thickness. One of its characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127 degrees, 144 degrees, 165 degrees, etc. have corresponding hinges to match, so that various cabinet doors can be stretched accordingly. Spend.

Door hinge: It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, copper bearing hinges are mostly used. Because of its beautiful and bright style, moderate price, and equipped with screws.

Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible, and it is mostly used on heavy-duty doors or special steel frame steel doors.

Inclined release hinge: This kind of hinge makes use of the inclined plane of the hinge and the weight of the door leaf to automatically close the door. It is mainly suitable for lighter wooden doors or half-section doors such as toilets.

The above recommendations are about the characteristics of the hidden hinge and the precautions for installation. From this, we can know that this hidden hinge can be divided into adjustable hidden hinges and non-adjustable hidden lotus leaves, and the product is easy to install. It can be used on invisible doors, and there are a variety of adjustment directions for us to choose from. However, the specific operation effect in the later stage depends on the choice between the hidden door hinge parts. You can continue to understand the above, combined with the actual choice. A hidden spectrum and you can also refer to other classification knowledge of the hinge page for an in-depth understanding.

what is hinge

Hinge definition:

Hinge: also known as hinge. It is composed of a pair of metal leaves (or parts) connected by pivot pins, usually in two folds. It is a device by which two parts of furniture doors, covers or other parts that need to swing are connected and rotated.

Names of countries:

Chinese: hinge; hinge

German: Scharnier

English: Hinge

Spanish: Bisagra

French: Charnire (menuiserie)

Japanese: Butterfly

Classification of hinges:

1. Ordinary hinges: mainly used for cabinet doors, windows, doors, etc. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After installing the hinges, various bumpers must be installed, otherwise they will swing easily.

2. Special-shaped hinges: Compared with ordinary hinges, special-shaped hinges have the same function as ordinary hinges, but the structure is slightly different from ordinary hinges. It is mainly used in industrial products, such as flag-shaped hinges and spring hinges. types of pages.

The hinge is generally composed of the following accessories: 1. Hinge sheet; 2. Hinge shaft; 3. Hinge bearing (not necessary); 4. Hinge cap.

3. Common specifications of hinges: 2 inches (length 50mm), 2.5 inches (length 65mm), 3 inches (length 75mm), 4 inches (length 100mm), 5 inches (length 125mm), 6 inches (length 150mm).

English hinge cap term explanation:

FT---Flat tip (flat head) BT---Ball tip (ball head)

PT---Pagoda tip (pagoda head) GT---Acorn tip (acorn head)

CT---Crown tip (crown head) ST---Steeple tip (spire head)

(Jieyang Jingtai Hardware Fittings Factory http://www.cngtxc.com/Scripts/content/knowledge/knowledgeHinge1.html

Hinge Type Encyclopedia

The types of hinges include ordinary hinges, pipe hinges, and door hinges.

1. Ordinary hinge

In any era, ordinary represents the public and represents the trend at that time. In terms of doors, windows and furniture, the ordinary type is the most common, and the hinges corresponding to these ordinary furniture are also indispensable. Therefore, the most common type on the market The hinge type is the ordinary type, which does not have the function of a spring hinge.

2. Pipe hinge

This is a kind of spring hinge, which is to add a spring in the middle of the hinge to better control the opening and closing of doors, windows and furniture. It is worth mentioning that this kind of hinge is most commonly used in the connection of furniture door panels. The There are galvanized iron and zinc alloy hinges. The biggest feature is that the height and radian of up, down, left, and right can be adjusted, and the opening angle can even be determined according to the size of the room.

3. Door hinge

This is a highly targeted hinge, mainly used for the connection and rotation of the door leaf and the door frame. This type of hinge is made of copper or stainless steel, and it is also divided into ordinary type and bearing type. And the above mentioned Compared with the two hinges, the door hinge has the largest load-bearing capacity and is durable.

hinge

Hinge is also known as hinge, and its official name is hinge. It is often composed of two folds, which is a part that connects two parts of an object and enables it to move. Ordinary hinges are used for cabinet doors, windows, etc.; the materials are iron and copper. And stainless steel. The pipe hinge is also called a spring hinge; it is mainly used for the connection of furniture door panels, and it generally requires a plate thickness of 16 to 20 mm.

What hinges are used for invisible doors and installation precautions

What hinges are used for invisible doors and installation precautions

What hinges are used for invisible doors and installation precautions? Many people have only heard of invisible doors, but they have never seen invisible doors. For invisible doors, they are integrated with the wall of the wardrobe. It is impossible to tell from the color that it is a door. , about the invisible door, let's take a look together, what hinges are used for the invisible door and installation precautions.

What hinges are used for invisible doors and installation precautions1

Generally speaking, the invisible door is used on the door next to the TV background wall, and it needs to be normally closed to achieve the invisible effect. However, the invisible door cannot have a handle from the outside, so it needs a hinge that will automatically close.

What hinges are used for invisible doors

1. Spring hinge

It can be normally closed, but it has great disadvantages. For example, there is no buffer when closing the door, which will damage the door. If there are children at home, the child's hand may be caught, so this kind of hinge is not recommended for everyone.

2. Hydraulic buffer hinge

It can be closed automatically, and it has a buffer when it is closed, which can better protect the door body. The disadvantage is that the indoor ventilation is relatively poor.

3. Door closer hinge

It is a hinge with the effect of a door closer, with cushioning and a door stopper. When the door is opened to 90 degrees, it can stop there, which can achieve better ventilation.

When you choose and buy, you have to check it yourself. Open one hinge horizontally, and the other will neither move nor close all at once, but slide down slowly. OK.

Invisible door installation precautions

1. Install the handle and lock on the side that does not need to be hidden. If you must press the handle on the hidden side, then it is not a bad idea to choose a decorative handle. Do not install the door handle, but it is convenient to control the door without a handle open closed? A reasonable way is to use multifunctional hydraulic hinges, hidden hinges, floor springs, touch pop openers and door closers.

2. The key of the invisible door is the hydraulic hinge or hidden hinge. It not only connects the door and the wall to rotate, but also has super load-bearing capacity, so choose a hard and high-quality hydraulic hinge or hidden hinge Particularly important.

3. The door closer can make up for the defect that there is no handle. It can avoid damage to the door panel or door pocket by closing the door slowly and automatically.

4. The floor spring is mainly used for invisible doors with 360-degree central axis rotation, and its fixation is relatively stable.

5. The touch rebounder is used for the outward-opening invisible door, which is not necessary for the inward-opening type.

6. In order to maintain occasional indoor ventilation, you can press a door stopper so that the door can be kept open. If conditions permit, families can consider building a fresh air system.

7. Be sure to align the door panel outward with the wall, on the same horizontal plane, the transition area is smooth and not abrupt, and the gap is narrow, like a complete wall.

The above is the introduction of relevant knowledge about what hinges to use for invisible doors and precautions for installing invisible doors. I hope it will be helpful to those who install invisible doors. Invisible doors are generally used in offices and home life in various ways, and some are directly set on On the walls, some are behind the display racks and Duobaoge, and some even the entire wall is an invisible door. If you want to know more about it, you can follow us.

What hinges are used for invisible doors and installation precautions2

Invisible door hingehow to install and use the hinge

1. When installing a wooden door (slotted installation), first tighten the door and the door frame, slot the contact surface between the door and the door frame (for installing two small hinges), and install the two large hinges when the door is closed. The hinges are respectively fixed on the door and the door frame with screws, and then the door is opened to a 90-degree positioning state, and the two small hinges are respectively fixed on the door and the door frame with screws, and the completion is complete.

2. When installing aluminum alloy or plastic steel doors (or installing wooden doors without slots), first install the hinges on the door frame, and then open the hinges to the automatic fixed position (that is, the position when the door is opened to 90 degrees), Put the door leaf into the door frame (closed state), then close the hinge, and fix the hinge on the door leaf to complete the work.

3. The positioning function is fixed by steel balls, and the fixing force is determined by the top wires at both ends of the tube, which can be adjusted appropriately with a screwdriver.

Invisible door hinge - invisible door hinge installation

Step 1: Align the raised alignment line on the back of the hinge with the door leaf and the door frame and draw the slotting line.

Step 2: When slotting, pay attention to the subtle changes in the slotting depth. It should be designed according to the slope shape of the blade thickness. Protrude from the plane of the door leaf or the plane of the door frame, but do not make the groove too deep. The hinge and the surface of the door should be kept on the same level as possible.

Step 3: First fix the upper hinge on the door leaf, and then fix the lower hinge on the door frame. When installing, make the hinge open at a position above 90 degrees (the hinge will automatically close when it is less than 80-90 degrees). Check the hinge After installation, open and close the door leaf several times to see if it moves smoothly.

Step 4: Turn on the hinge function. Use a Phillips screwdriver to remove the start screw, and the invisible door hinge starts to work. If the speed and strength of the hinge are not suitable for debugging, you can adjust it through the speed regulating screw.

The above is the use and installation method of the invisible door hinge summarized by Comfort 100. I hope it will be helpful to everyone. Invisible doors are more popular now. The most important reason for the success of invisible doors is the choice of hinges. A suitable invisible door is not only conducive to opening, but also can make the door gap smaller, making the invisible door perfectly integrated with the surrounding.

Is it better to use hydraulic hinges or hinges for invisible doors?

Hydraulic hinges are good for invisible doors.

1. Hinges and hidden doors need to solve the problem of no handle. First of all, the handle is used to pull the door. Without a handle, there is no way to close the door. Therefore, there must be a device that can automatically close the door to replace the automatic door lock. The handle can not be installed;

2. The door, the door needs to be installed on the wall. First of all, there are various doors with different patterns and shapes. The only one is installed on the door frame. When the door is closed, it must Once the wall is leveled, the only way is to move the door forward, keep the wall in a horizontal position, and after installation, make various patterns on the door that are the same as the wall to hide the existence of the door;

3. Door lock, door lock is also very critical. When the bathroom is hidden, a lock must be installed inside to avoid embarrassment. The hidden lock must have nothing outside. There can be knobs and handles inside, and nothing outside.

Of course, there is no way to lock the door outside. Some netizens said that there is no handle and keyhole outside, so there is no way to lock the door. Will it be blown open by the wind? This problem is very serious, if you want not to blow the door open, see the detailed explanation below;

4. If you want to make a hidden door, the most critical, most important, and most difficult part is to solve the automatic closing device, that is the hinge. There are many kinds of automatic closing hinges, including spring hinges and ordinary hinges. Hinges, but they cant be used. The spring hinges have no cushioning function. It is easy to close the door and damage it, and it is easy to pinch the childs hand. Do not use it.

, These are the top ten invisible door hinges with good sales this year. To answer the question of which brand is the best in the top ten brands of invisible door hinges, the author has a relatively long time and experience in online shopping. It is recommended that you analyze the following two points. The first is to choose a merchant with a large sales volume. The large sales volume indicates that the invisible door hinges in this store are very popular; the other is to look at the user's evaluation. , and the praise rate is high, and customers will tell their experience; fully consider these two points when choosing, and your shopping will be perfect. Naturally, Qiu Ruisi is not willing to hold Lin Yu immediately Yi's other hand retorted

How about Yagu invisible door hinge

The Yagu invisible door hinge is very good. The material of the Yagu invisible door hinge is aluminum alloy, which is wear-resistant and compressive. According to the relevant public information, the thickness of the Yagu invisible door hinge is 3.5 decimeters, which is higher than that of the same product on the market. of better quality.

Invisible door hinge purchase skills Invisible door aluminum alloy hydraulic hinge installation skills

Now that the application of invisible doors in home decoration is becoming more and more extensive, the purchase of hinges is very important. So, what are the tips for purchasing invisible door hinges? What is the installation technique of aluminum alloy hydraulic hinge for invisible door? Let's find out together.

Now that invisible doors are more and more widely used in home decoration, the purchase of hinges is very important. So, what are the tips for purchasing invisible door hinges? What are the installation skills for invisible door aluminum alloy hydraulic hinges? We Take a look.

1. Invisible door hinge selection skills

1. The hinge is placed inside the door leaf. If the hinge breaks during use, the consumer will not notice it. When an accident occurs, the entire door panel will be knocked down on the ground. The repair cannot be immediate and can only be returned to the factory. The reason for the built-in hinge will extend the repair time to one month or more, causing some inconvenience to customers. Therefore, when you choose an inner door, you should try to choose an exposed hinge under the premise of considering a big brand. Can save some unnecessary trouble!

2. Good hinges include brass and stainless steel. Generally, the yellower the brass hinges, the better, which indicates that the copper content is high. The poor hinges will cut corners and fail to meet the standards in terms of specifications and thickness. Good hinges The page thickness is about 3 mm, and the hinge page is relatively thin. It is recommended that you buy stainless steel, pay attention to the thickness of the steel plate, generally there are different thicknesses such as 3 mm or 4 mm, the price is different, and the thick one is durable.

3. Spread out a hinge horizontally. The hinge does not move, nor does it fall off all at once, but slides down slowly. This kind of hinge will not take much effort to close, and will not hit the door all at once. To the door frame, it is a good hinge. At present, the hinges used for interior doors have mute devices in their rotating parts, that is, the middle shaft is thicker, and it is a wear-resistant mute bearing. Hinges with good sealing performance should be selected , When purchasing, open and close, pull several times to feel its flexibility and convenience.

2. Installation skills of aluminum alloy hydraulic hinges for invisible doors

1. Before installation, be sure to check whether the hinge matches the door and window frames and leaves.

2. It is necessary to check whether the hinge groove matches the height, width and thickness of the hinge.

3. Check whether the hinge and the screws and fasteners connected to it are matched.

4. The connection method of the hinge should match the material of the frame and leaf, such as the hinge used for the steel frame wooden door, the side connected to the steel frame is welded, and the side connected to the wooden door leaf is fixed with wood screws.

5. When the two leaf plates of the hinge are asymmetrical, it should be identified which leaf plate should be connected to the fan, which leaf plate should be connected to the door and window frame, and the side connected to the three sections of the shaft should be fixed to the frame , the side connected to the two sections of the shaft should be fixed to the frame.

6. When installing, it should be ensured that the shafts of the hinges on the same leaf are on the same vertical line, so as to prevent the door and window leaves from springing up.

The above is the relevant knowledge about the purchase skills of invisible door hinges and the installation skills of aluminum alloy hydraulic hinges for invisible doors that we introduced. As long as you follow the above, you will avoid some unfavorable factors.

What hinges are used for invisible doors

The first is to see what price you want to choose, the second is to see what functions you need, and then the weight of the door. The 30-yuan invisible door hinge is made of cold-rolled strip steel, with special anti-rust treatment, color galvanized, and then sprayed with silver powder or gold powder. The hinge. Height (4 inches) 10cm, single-piece hinge width 2.6cm, unfolded width 6.5cm, hinge piece increased thickness 1.6mm, three bearing capacity 80kg. When the door is opened more than 90 degrees, the door will be automatically locked, when the door is opened When the temperature is lower than 90 degrees, the door will automatically close, and it will not slam when it is closed at the end. It has a feeling of damping. The invisible door hinge specification of 200 yuan: 5*4*3.0 thickness, surface: stainless steel wire drawing, Material: cold-rolled steel, with door stop buffer function

Integrating door closer, hinge and door stopper, generally used for standard door thickness

The door thickness is above 3.8 cm. The difference from RMB 30 is that this one is hydraulic and the other one is spring. This one can be positioned at will between 70 and 90 degrees, and the door will close automatically when it is less than 70 degrees. The closing speed can be adjusted, and it has a damping function. .More expensive is the difference in quality and sensitivity

What hinges and installation precautions are used for invisible doors What are the hinges and installation precautions for invisible doors

1. Spring hinge: It can be normally closed, but it has great disadvantages. For example, there is no buffer when closing the door, which will damage the door. If there are children at home, the child's hand may be caught, so it is not recommended to use this kind of hinge.



2. Hydraulic buffer hinge; it can be closed automatically, with its own buffer when closed, which can better protect the door body. The disadvantage is that the indoor ventilation is relatively poor.



3. Door hinge: It is a hinge with the effect of a door closer, with cushioning and a door stopper. When the door is opened to 90 degrees, it can stop there, which can achieve better ventilation.



4. Install the handle and lock on the side that does not need to be hidden. If you must press the handle on the hidden side, then it is not a bad idea to choose a decorative handle. It is best not to install a door handle, but it is convenient to control the door without a handle Opening and closing? The most reasonable way is to use multifunctional hydraulic hinges, hidden hinges, floor springs, touch pop openers and door closers;



5. The key to the invisible door is the hydraulic hinge or hidden hinge. It not only connects the door and the wall to rotate, but also has super load-bearing capacity, so choose a hard and high-quality hydraulic hinge or hidden hinge Particularly important.



6. The door closer can make up for the defect that there is no handle. It can avoid damage to the door panel or door pocket by closing the door slowly and automatically.



7. The floor spring is mainly used for the invisible door with 360-degree central axis rotation, and its fixation is relatively stable.



8. The touch-type rebounder is used for the outward-opening invisible door, which is not necessary for the inward-opening type.



9. In order to maintain occasional indoor ventilation, you can press a door stopper so that the door can be kept open. Families with conditions permitting can consider building a fresh air system.

What is the difference between hinges and hinges, which one is better for invisible doors in home decoration

What are hinges and hinges?

What is the difference between a hinge and a hinge

The hinge is the same as the hinge, which is a furniture copper ornament. It is often composed of two folds. It is a metal part that connects two parts of the furniture and can make it move. It belongs to the system with a rotating shaft. The hinge is also called the hinge. It is used to connect two A mechanical device that is solid and allows rotation between two. May consist of movable components, or of collapsible material.

hinge

Used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After the hinges are installed, various bumpers must be installed, otherwise the wind will Blow the door.

The opening and closing of the window sash is too fast, if you dont pay attention to it, the strong swing will easily hit the hinge into internal damage, causing the window to fall, and there is no sign of the window falling. Because only one hand screw is used to support the force point of the wind force 20 kg window sash, the structure is seriously unreasonable.

Difference between hinge and hinge

Hinge

The launch of the safety positioning hinge solves structurally the overweight window sash, which causes the drop, the opening and closing too tight, and the mutual wear in all aspects, so as to ensure the service life of the window sash and the safety of the window sash.

The hinge can provide a certain amount of friction, so it can be used alone, and the one used on the casement window is slightly different from the one used on the upper swivel window, and the length of the outer arm connected to the window frame is different.

How to choose invisible hinge door?

1. Good hinges include brass and stainless steel. Generally, the yellower the brass hinges, the better, which indicates that the copper content is high. The poor hinges will cut corners and fail to meet the standard in terms of specifications and thickness. Good hinges The thickness of the page is about 3 mm, and the difference page is relatively thin. It is recommended that you buy stainless steel, pay attention to the thickness of the steel plate, generally there are different thicknesses such as 3 mm or 4 mm, the price is different, and the thick one is durable. Generally speaking, it should be Choose a 4mm thick one, the price is about 15-25 yuan (one pair of two), which is also related to the treatment process of the hinge surface. Of course, good stainless steel can be 80 yuan/pair.

2. Expand a hinge horizontally. The hinge does not move, nor does it fall off all at once, but slides down slowly. This kind of hinge is neither strenuous to close, nor will it hit the door all at once To the door frame, it is a good hinge. At present, the hinges used for interior doors have mute devices in their rotating parts, that is, the middle shaft is thicker, and it is a wear-resistant mute bearing. Hinges with good sealing performance should be selected , When purchasing, open and close, pull several times to feel its flexibility and convenience.

What are the advantages of damping hinges

Damping hinges, also known as buffer hinges, hydraulic hinges, rely on a brand-new technology to adapt to the closing speed of the door. The product uses hydraulic buffer technology to make the door open slowly when the opening is not greater than 60, which can reduce the impact. Force, forming a comfortable effect when closing, even if the door is closed with force, it will make the door close gently; ensure perfect and soft movement. Prevent children from pinching and so on! !

What is the difference between big bend, medium bend and straight bend of damping hinge, and how to distinguish

1. The gap is different: there is a gap between the two big bends of the hinge. There is a required minimum gap between the middle bends of the hinge.

2. The hinges are different: the middle bend of the hinge requires the use of a hinge with a curved hinge arm. The straight bend of the hinge requires the use of a hinge with a very curved hinge arm.

3. The position is different: the door panels with large curved hinges all cover the side panels of the cabinet. The two doors bent in the middle of the hinge share a side panel. The door with straight curved hinges is located in the cabinet, next to the side panel of the cabinet.

Extended information:

Selection skills of damping hinges:

Appearance is very basic. When purchasing, check how smooth the surface material of the damping hinge is. If there are problems such as scratches and deformation, do not choose it. These are generally produced by secondary processing of waste materials. , not only the appearance is ugly, no grade, the quality is not guaranteed.

The most important thing about the hinge is the switching function, and the damping hinge is a hydraulic hinge, which has higher requirements for the switch. You can check the damper, rivet assembly, etc., and also check whether there is noise when opening and closing, whether the turning speed is uniform, etc. , even if there are some small problems, it is not good.

Usually the hinges are equipped with screws, these are adjustment screws, which can be used to adjust the hinge in three dimensions up and down, front and back, left and right. When we buy damped hinges, we can use a screwdriver to adjust the screws three to four times, and then remove the screws to see the hinge arm Whether the thread on the thread is damaged, thread on thread is relatively easy to wear, and if the thread on the thread is not accurate enough, it is easy to slip and cannot be twisted.

Reference source:
damping hinge

called the hinge;

Hinges, also known as hinges, are mechanical devices used to connect two solids and allow relative rotation between them. Hinges can be composed of movable components or foldable materials. Hinges are mainly installed on doors and windows, The hinges are more installed on the cabinets. According to the material classification, they are mainly divided into stainless steel hinges and iron hinges; in order to let people enjoy better, hydraulic hinges (also known as damping hinges) have appeared. It has a buffer function, which minimizes the noise caused by the collision with the cabinet when the cabinet door is closed.

common classification

1. According to the type of base, it can be divided into detachable type and fixed type;

2. According to the type of arm body, it is divided into two types: slide-in type and snap-in type;

3. According to the cover position of the door panel, it is divided into full cover (straight bend, straight arm) with a general cover of 18%, and a half cover (medium bend, curved arm) with a cover of 9%. The built-in (large bend, large bend) door panels are all hidden inside;

4. According to the development stage of the hinge, it is divided into: one-stage force hinge, two-stage force hinge, hydraulic buffer hinge, touch self-opening hinge, etc.;

5. According to the opening angle of the hinge: generally 95-110 degrees are commonly used, and special ones are 25 degrees, 30 degrees, 45 degrees, 135 degrees, 165 degrees, 180 degrees, etc.;

How to distinguish between damping hinges and ordinary hinges

Damping hinge is a kind of hinge, also known as hydraulic hinge, which relies on hydraulic damper to adjust the closing speed of the door. Even if the door is closed with force, it will close gently, ensuring perfect and soft movement.

The overall structure of the damping hinge includes a support, a door box, a buffer, a connecting block, a connecting rod and a torsion spring. One end of the buffer is hinged on the support; the middle of the connecting block is hinged on the support, one side is hinged with the door box, and the other It is hinged with the piston rod of the buffer; the connecting block, connecting rod, support, and door box form a four-bar linkage; the buffer includes a piston rod, a housing, and a piston, and there are through holes and holes on the piston, and the piston rod When the piston is driven to move, the liquid can flow from one side to the other through the through hole, thus playing a buffering role.

The biggest difference between damped hinges and ordinary hinges is that a damper (usually a small cylinder) is added to the hinge.

How to choose the damping hinge correctly

Damping hinge selection basis:

1: Determine the damping force of the selected hinge according to the required damping force of the door

2: Select the hinge shape, opening angle, material, color, service life, damping breakpoint, etc. according to the working conditions.

3: Select the hinge type according to the interior door and exterior door

Real life common ball hinge principle

Hinges, also known as hinges, are mechanical devices used to connect two solids and allow rotation between them. Hinges may be composed of movable components or foldable materials. Hinges are mainly installed on doors and windows, while Hinges are more installed on cabinets. According to the classification of materials, they are mainly divided into stainless steel hinges and iron hinges; in order to let people enjoy better, hydraulic hinges (also known as damping hinges) have appeared. The buffer function minimizes the noise from the collision with the cabinet when the cabinet door is closed.

Working principle: The rotating pair composed of a cylindrical pin, a hole and its two ends is called a hinge. An object A is set on a part C of another object B. The movement of object A is limited by C, but A can revolve around C in Objects A and B form a hinge when they rotate in a plane or in space (C is spherical).

What is the working principle of the damper

working principle:

The main part of the damper is two counterweight objects each weighing about 150 tons suspended by steel cables, suspended on the 90th floor (395 meters). When strong winds hit, the device uses sensors to detect wind force and building The shaking degree of the object, and the computer controls the counterweight object to move in the opposite direction through the spring and hydraulic device, thereby reducing the shaking degree of the building.

Its working principle is like a person on a rocking boat, moving his body in the opposite direction of the boat's shaking to achieve balance. If a strong wind blows from the north, the counterweight is like a huge "pendulum" swinging to the north, making the The wind damper will generate a force that is opposite to the wind direction, thereby defusing the degree of shaking of the building and counteracting the impact of strong winds on the building.

After using this device, the acceleration of the strong wind on the building can be reduced by about 40%, so that even if it is hit by a strong wind, the people in the building will basically not feel the shaking of the building.

Extended information:

Classification:

The damper is just a component. It has different damping effects when used in different places or in different working environments. Damper: used for vibration reduction; Snubber: used for shock resistance, allowing movement at low speeds, locking when the speed or acceleration exceeds the corresponding value, form a rigid support.

Various applications are: spring dampers, pulse dampers, rotary dampers, wind dampers, viscous dampers, damped hinges, damped slide rails, furniture hardware, cabinet hardware, etc.

Scope of application:

Hydraulic dampers are mainly suitable for anti-vibration of pipelines and equipment in nuclear power plants, thermal power plants, chemical plants, steel plants, etc. They are often used to control impact fluid vibrations (such as rapid closing of the main valve, discharge of safety valves, water hammer, breaking The vibration of the piping system stimulated by the impact of pipes, etc.) and earthquakes; the liquid damper cannot effectively control the low-amplitude high-frequency or high-amplitude low-frequency vibration, and the spring damper is suitable for this occasion.

References: Damper

What is the principle of the slow-down of the damping of the toilet seat? !

When the toilet falls, it drives the rotating shaft to rotate, and squeezes the damping oil from the direction of the large hole to the direction of the small hole through the screw. It is generally used when the cover plate is heavy, and it is filled with a certain amount of damping oil. There is a rotating shaft in the middle, and the rotating shaft is processed into Spiral, discharged from the direction of the small hole, so it can only be discharged slowly, so as to realize the function of slow down of the toilet.

Damping helps reduce the resonance amplitude of the mechanical structure, thereby avoiding structural damage due to the vibration stress reaching the limit; damping helps the mechanical system quickly return to a stable state after being subjected to an instantaneous impact.

Damping helps to reduce the sound radiation caused by mechanical vibration and reduce mechanical noise. The noise of many mechanical components, such as the housing of transportation vehicles and saw blades, is mainly caused by vibration. The use of damping can effectively suppress resonance. thereby reducing noise.

Extended information:

When = 1, the solution is a pair of heavy real roots, and the damping form of the system at this time is called critical damping. In real life, the doors of many rooms or bathrooms in many buildings are equipped with torsion springs for automatic door closing. The floor is equipped with damping hinges, so that the damping of the door is close to the critical damping, so that when people close the door or the door is blown by the wind, it will not cause too much noise.

In actual vibration, since the frictional force always exists, the energy initially obtained by the vibration system will continue to perform negative work on the system due to the resistance during the vibration process, so that the energy of the system will continue to decrease, the intensity of the vibration will gradually weaken, and the amplitude will also decrease. It becomes smaller and smaller, so that the vibration finally stops, and the mechanical energy of the system like this is gradually reduced due to friction and conversion into internal energy, and the amplitude of the vibration weakens with time.

Reference source: - Damping

Reference source: - Damping

Working principle of random stop

Working principle: The revolving pair composed of a cylindrical pin, a hole and its two ends is called a hinge. An object A is set on a part C of another object B. The movement of object A is limited by C, but A can revolve around C. Rotate in plane or space, objects A and B form a hinge.
The reel is connected to the other end of the rope. The reel includes a first reel and a second reel. One end of the rotating shaft is connected to the first reel through a connecting regulator and through the bearing frame, and the other end passes through the other end. The bearing frame is connected with the second reel.

Introduction of hinge

Hinges, also known as hinges, are mechanical devices used to connect two solids and allow rotation between them. Hinges may be composed of movable components or foldable materials. Hinges are mainly installed on doors and windows, while Hinges are more installed on cabinets. According to the classification of materials, they are mainly divided into stainless steel hinges and iron hinges; in order to let people enjoy better, hydraulic hinges (also known as damping hinges) have appeared. The buffer function minimizes the noise from the collision with the cabinet when the cabinet door is closed.

The automatic stop device includes a bottom shell, a cover plate, a drum, a reel, and a connecting regulator. The top of the bottom shell is connected to the cover plate. There is a set of bearing frames near both ends of the bottom shell, and a rotating shaft is arranged between the two bearing frames. One end of the connection regulator is fixed on the bearing frame. One end of the roller is connected to the bearing frame, and the other end of the roller is connected to the end of the bottom shell.

What is the working principle of the hinge

The hydraulic buffer hinge adopts the environmental protection design concept of small structure design, and the miniature hydraulic damper is cleverly hidden in the hinge. It is a combination of advanced hydraulic buffer system, unique transmission system (patented), high-performance manganese steel elastic system The advanced technology is integrated in the hinge, which can make the cabinet door close automatically and slowly, and can truly achieve the functions of cushioning, anti-collision, and noise reduction.

Extended information

A formed hydraulic hinge is composed of many parts, and these parts are all stamped out by molds. The raw material is 304 stainless steel, but the stamping molds are all iron, which will generate mechanical magnetism during processing.

Moreover, the fittings in the hinge are made of stainless iron, which also has suction through 304. The main parts are all pure 304, and the other small parts are made of stainless steel. It is easy to break, so it will definitely be sucked directly with a magnet, which is a normal phenomenon.

Reference source: Baidu Encyclopedia - hydraulic hinge