to the Installation Method of Spring Hinges: Step-by-Step GuideSpring hinges are a type of hinge that automatically closes the door after it is opened. They are equipped with a spring and an adjusting screw, which allows for the adjustment of the height and thickness of the plates in various directions. There are two types of spring hinges: single spring hinges that only open in one direction, and double spring hinges that can be opened in both directions.Before installing spring hinges, it is important to ensure that the hinge matches the door and window frame and the door leaf. Check if the hinge groove matches the height, width, and thickness of the hinge, and also check if the hinge and the screws and fasteners connected to it are matched.The method of connecting the spring hinge should match the material of the frame and leaf. For example, if the hinge is used for a steel frame wooden door, the side connected to the steel frame should be welded, while the side connected to the wooden door leaf should be fixed with wood screws. If the leaf boards are asymmetrical, it is important to identify which leaf board should be connected to the fan and which leaf board should be connected to the door and window frame. The side connected to the three sections of the shaft should be fixed to the frame, and the side connected to the two shaft sections should be fixed to the door and window.To install the spring hinge, follow these steps:1. Insert a 4mm hexagonal key into the hole at one end of the hinge and press it firmly to the end while opening the hinge.2. Install the hinges into the hollowed-out grooves on the door leaf and door frame using screws.3. Close the door leaf and make sure the spring hinges are in the closed state. Insert the hexagonal key again without pressing it down, and turn it clockwise to rotate. You should hear the sound of the gears meshing four times. It is important not to exceed four times because twisting the spring beyond its limit can damage it and cause it to lose its elasticity when the door leaf is opened.4. After tightening the hinge, make sure the opening angle does not exceed 180 degrees.5. If you want to loosen the hinge, simply follow the same procedure as in step 1.The recommended spring hinges are designed with a spring device, which allows for a wider scope of application compared to ordinary hinges. They are commonly used on spring doors. When choosing a spring hinge, consider the door type, door frame material, shape, and installation direction.Cabinet Hinges Installation Method: Step-by-Step GuideThe installation of cabinet hinges is also an important process. Follow these steps to install cabinet hinges properly:1. Measure the size and edge of the cabinet door and mark them accurately.2. Drill holes on the door panel. The depth of the hole should not exceed 12mm.3. Insert the hinge into the hinge cup, and then put the hinge on the door panel hole of the cabinet and fix it.4. Check whether the hinge can be used normally by opening and closing the cabinet door.It is important to note a few things when installing cabinet hinges:- Avoid situations where multiple hinges share the same side panel. If this cannot be avoided, provide an appropriate spacing when drilling to avoid multiple hinges being fixed at the same position.- When installing the hinge, ensure that the hinge connection part, length, and width are consistent. If the covering distance of the fixed machinery is reduced, consider choosing a hinge with a curved hinge arm.- Check whether the hinge screw matches the fastener, and select the appropriate hinge according to different conveying levels.- When installing the hinge, ensure that the hinges on the same leaf are on the same vertical line to avoid instability and misplacement of the mechanical objects.Sometimes, cabinet doors become tight due to frequent use, causing the hinges to loosen. In this case, a simple adjustment can solve the problem. Using a screwdriver, loosen the screw that fixes the hinge base, slide the hinge arm to the correct position, and then tighten the screws again.In conclusion, the installation of spring hinges and cabinet hinges requires careful attention to detail. By following the step-by-step guides provided, you can ensure proper installation and achieve satisfactory results.

to the installation method of spring hinges:Spring hinges are specialized hinges used on spring doors or other cabinet doors. When selecting spring hinges, it is important to consider the specific requirements and specifications of the door or cabinet. The installation process of spring hinges requires careful attention to the following steps and precautions to ensure proper functionality and durability.1. Brief introduction of spring hinge:A spring hinge is designed to automatically close a door once it has been opened. It consists of a spring and an adjusting screw, which allows for height and thickness adjustments of the plate in all directions. There are single spring hinges that open in one direction only, and double spring hinges that allow for two-way opening. The latter is commonly used in public buildings due to its compact structure, advanced design, and durability. Equipped with a stainless steel hinge head, strong elastic iron spring, and high-quality resistant oil, spring hinges provide smooth, stable, and noiseless operation.2. Spring hinge installation method:Before installing spring hinges, it is important to ensure that the hinge matches the door and window frame and leaf. Check if the hinge groove matches the height, width, and thickness of the hinge. Also, ensure that the hinge is properly connected with the screws and fasteners. The method of hinge connection should be suitable for the material of the frame and leaf. For example, hinges used for steel frame wooden doors should be welded on the side connected to the steel frame, while wood screws should be used on the side connected to the wooden door leaf. In the case of asymmetrical leaf boards, it is necessary to identify which leaf board should be connected to the fan, and which should be connected to the door and window frame. The side connected to the three sections of the shaft should be fixed to the frame, and the side connected to the two shaft sections should be fixed with the door and window. It is important to ensure that the shafts of the hinges on the same leaf are on the same vertical line to prevent the door and window leaf from springing up.The installation steps for spring hinges are as follows:1. Insert a 4mm hexagonal key into the hole at one end of the hinge and press firmly until the hinge opens.2. Install the hinges into the hollowed-out grooves on the door leaf and door frame using screws.3. Close the door leaf and set the spring hinges in the closed state. Insert the hexagonal key again, this time turning it clockwise until you hear the sound of the gears meshing four times. Do not exceed four turns, as it may damage the spring and reduce its elasticity when the door leaf is opened.4. Once the hinges are tightened, ensure that the opening angle does not exceed 180 degrees.5. To loosen the hinge, simply repeat the steps above.The above method of installing spring hinges provides more flexibility and functionality compared to ordinary hinges. By following these steps and considering the specific requirements of the door or cabinet, you can achieve a steady and reliable operational effect.Expanded Spring hinges are specialized hinges designed to automatically close doors after they have been opened. These hinges are equipped with a spring and an adjusting screw, allowing for adjustments in height and thickness of the plate in all directions. There are two types of spring hinges - single spring hinges and double spring hinges. Single spring hinges are designed to open in one direction only, while double spring hinges can be opened in both directions, making them suitable for use on the gates of public buildings.The installation process of spring hinges involves several steps and precautions that need to be understood to ensure proper functionality. Before installing spring hinges, it is important to check whether the hinges match the door and window frame and leaf. This includes checking whether the hinge groove matches the height, width, and thickness of the hinge, and whether the hinge is properly connected with the screws and fasteners. The method of hinge connection should be appropriate for the material of the frame and leaf. For example, when installing hinges on steel frame wooden doors, the side connected to the steel frame should be welded, while the side connected to the wooden door leaf should be fixed with wood screws.Additionally, it is important to identify which leaf board should be connected to the fan and which should be connected to the door and window frame, especially if the leaf boards are asymmetrical. The side connected to the three sections of the shaft should be fixed to the frame, while the side connected to the two shaft sections should be fixed with the door and window. To prevent the door and window leaf from springing up, it is crucial to ensure that the shafts of the hinges on the same leaf are on the same vertical line.The installation steps for spring hinges are as follows:1. Insert a 4mm hexagonal key into the hole at one end of the hinge and press firmly until the hinge opens.2. Install the hinges into the hollowed-out grooves on the door leaf and door frame using screws.3. Close the door leaf and set the spring hinges in the closed state. Insert the hexagonal key again, this time turning it clockwise until you hear the sound of the gears meshing four times. It is important not to exceed four turns, as this may damage the spring and reduce its elasticity when the door leaf is opened.4. Once the hinges are tightened, ensure that the opening angle does not exceed 180 degrees.5. To loosen the hinge, simply repeat the steps above.Spring hinges are recommended for their flexibility and functionality due to the inclusion of a spring device. They have a wider scope of application compared to ordinary hinges, particularly for use on spring doors. When selecting spring hinges, it is important to consider the specific requirements of the door or cabinet and choose accordingly.As for the installation of cabinet hinges, it is important to follow a step-by-step process. First, measure the size and edge of the cabinet door and mark them properly. Next, drill holes on the door panel, making sure not to exceed a depth of 12mm. Then, insert the hinge into the hinge cup and place it on the door panel hole of the cabinet. Fix the hinge in place. Finally, check whether the hinge can be used normally. Cabinet hinges play a crucial role in both the connection and longevity of cabinet doors. It is important to avoid situations where multiple hinges share the same side panel. If this cannot be avoided, be sure to leave an appropriate spacing when drilling to prevent multiple hinges from being fixed at the same position. After inserting the hinge into the hole of the cabinet door panel, ensure that the hinge arm is aligned and placed correctly. Additionally, check the compatibility of the hinge screw with the fastener, and choose the hinge according to the specific requirements of the cabinet. During installation, make sure that the hinges are in the same vertical line to avoid instability and misplacement of mechanical objects.Sometimes, cabinet doors may become tight due to frequent use. In such cases, it is a simple matter of readjusting the hinges. Using a screwdriver, loosen the screw that fixes the hinge base, slide the hinge arm to the correct position, and then tighten the screws. The installation of cabinet hinges may not be complicated, but it is necessary to determine the installation position of the cabinet door based on the size of the hinge.When installing cabinet hinges, it is important to determine the size of the cabinet door and the minimum margin between the cabinet doors. The minimum margin should be determined based on the type of hinge, which is generally listed in the cabinet hinge installation instructions. Once the installation is complete, test the opening and closing of the cabinet door to ensure a satisfactory effect. If adjustments are necessary, modify the cabinet door until the desired effect is achieved.In conclusion, the installation of spring hinges and cabinet hinges requires careful attention to detail and adherence to specific instructions. By following the steps and precautions outlined above, you can achieve a sturdy and reliable installation that ensures the proper functionality and longevity of your doors and cabinets.

How about hidden hinges? Types of hinges?



What I recommend for everyone today is the evaluation of hidden hinges and the knowledge of hinge types. From this, we can know that, first of all, common hidden hinges are different from ordinary full cover hinges. Their design It is quite special. If it is installed between the cabinet door and the wooden door, it will not be easy to find later. On the other hand, this hidden hinge also means that we can use it when we stand outside the door and install the lock on the left, or the door lock is installed It can also be used on the right side, so this kind of hinge is more in line with the actual characteristics of humanization, and they are easy to install, suitable for invisible doors, and there are many adjustment directions. You can refer to the following for details. We will explain these few for you. Aspects of evaluation and presentation analysis.

the
1. How about the hidden hinge

1. Beautiful hidden device, without any exposed parts, beautiful and generous! 2. Adjustable three-dimensional adjustable, the adjustment direction is up and down, left and right, and bevel adjustment. 3. The durable hidden hinge is made of imported No. 3 zinc , the service life is as long as 30 years! 4. Easy to install. After the factory has opened the hole and installed it, you only need to take the hexagon wrench to the customer and screw it on. 5. Save after-sales costs. When the door sags, the customer can pass the Manually adjust the hinge to adjust the door, which greatly saves the cost of the manufacturer's door after-sales. Real estate forum, decoration forum, owner forum, P3 V9 O- M3 T"



2. Types of hinges

Ordinary hinges: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After the hinges are installed, various touch beads must be installed. , otherwise the wind will blow the door panel.

Pipe hinge: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height of the plate up and down, left and right , Thickness. One of its characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127 degrees, 144 degrees, 165 degrees, etc. have corresponding hinges to match, so that various cabinet doors can be stretched accordingly. Spend.

Door hinge: It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, copper bearing hinges are mostly used. Because of its beautiful and bright style, moderate price, and equipped with screws.

Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible, and it is mostly used on heavy-duty doors or special steel frame steel doors.

Inclined release hinge: This kind of hinge makes use of the inclined plane of the hinge and the weight of the door leaf to automatically close the door. It is mainly suitable for lighter wooden doors or half-section doors such as toilets.

The above recommendations are about the characteristics of the hidden hinge and the precautions for installation. From this, we can know that this hidden hinge can be divided into adjustable hidden hinges and non-adjustable hidden lotus leaves, and the product is easy to install. It can be used on invisible doors, and there are a variety of adjustment directions for us to choose from. However, the specific operation effect in the later stage depends on the choice between the hidden door hinge parts. You can continue to understand the above, combined with the actual choice. A hidden spectrum and you can also refer to other classification knowledge of the hinge page for an in-depth understanding.

There are several hinges, how to distinguish

There are many types of hinges, which can be divided into different types according to different purposes.

1. According to the type of base, it can be divided into detachable type and fixed type.

2. According to the type of arm body, it is divided into two types: slide-in type and snap-in type.

3. According to the cover position of the door panel, it is divided into full cover (straight bend, straight arm) with a general cover of 18%, half cover (medium bend, curved arm) with a cover of 9%, and the built-in (large bend, large bend) door panels are all hidden inside.

4. According to the development stage of the hinge, it is divided into: one-stage force hinge, two-stage force hinge, hydraulic buffer hinge, touch self-opening hinge, etc.

5. According to the opening angle of the hinge: generally 95-110 degrees are commonly used, and special ones are 25 degrees, 30 degrees, 45 degrees, 135 degrees, 165 degrees, 180 degrees, etc.

6. According to the type of hinge, it is divided into: ordinary one-stage force hinge, two-stage force hinge, short arm hinge, 26-cup miniature hinge, marble hinge, aluminum frame door hinge, special angle hinge, glass hinge, rebound hinge, American hinge, damping hinge , thick door hinges and so on.

7. General hinges: used for cabinet doors, windows, doors, etc.

8. Spring hinges: mainly used for cabinet doors and wardrobe doors, which generally require a plate thickness of 18-20mm.

9. Door hinge: common type and bearing type.

10. Electromechanical cabinet hinges: used in electromechanical cabinet doors, mechanical equipment operation boxes and other products.

11. Heavy-duty hinges: used for large doors such as refrigerators and freezers, mostly made of zinc alloy.

12. The special-shaped hinge is also a corner hinge, with a large opening angle, which is also widely used in daily use.

13. Other hinges include countertop hinges, flap hinges, and glass hinges. Glass hinges are used to install frameless glass cabinet doors, and the glass thickness is required to be no more than 5-6mm. The style has holes and has all the properties of spring hinges.

A hinge, also known as a hinge, is a mechanical device used to connect two solids and allow relative rotation between them.

The difference between the three hinges of right angle (straight arm), half bend (half bend) and large bend (big bend)

No small bends.

Right-angle hinges (straight bends) allow the door to completely cover the side panels.

Half-bent hinges allow the door to partially cover the side panels.

Large curved hinges allow the door panels to be parallel to the side panels.

The middle bend is also called a half cover, which means that two doors share a side panel.

Extended information


Ordinary hinges: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel.

Pipe hinge: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a thickness of 16-20 mm.

Door hinge: It is divided into ordinary type and bearing type.

Other hinges: there are glass hinges, countertop hinges, and flap hinges.

Hinges are mainly installed on doors and windows, while hinges are more installed on cabinets.

The hinge is characterized by a buffer function when the cabinet door is closed, which minimizes the noise caused by the collision with the cabinet body when the cabinet door is closed.

The hinges are made of zinc alloy, steel, nylon, iron, stainless steel by powder coating, galvanized alloy, galvanized steel, sandblasting, chrome-plated zinc alloy, nickel-plated steel, brushed and polished.

Hinges are made of movable components, or of foldable material.


Reference source

Hinge
Hinge type introduction Classification information description

When it comes to hinges, we all know that it is a basic accessory product, often called a hinge, but the hinges in our impression are generally similar, mainly installed in some cabinet doors and windows or ordinary wood In the door, it can play the role of making it easy for everyone to open and close. But in fact, the hinge can be classified in detail, such as ordinary hinges, pipe hinges or door hinges. In addition to classification according to shape, the field of use The difference in location and location also determines their names. When purchasing, we should refer to the differences between different hinges to understand.

1. Types of hinges

Ordinary hinges: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After the hinges are installed, various touch beads must be installed. , otherwise the wind will blow the door panel.

Pipe hinge: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height of the plate up and down, left and right , Thickness. One of its characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127 degrees, 144 degrees, 165 degrees, etc. have corresponding hinges to match, so that various cabinet doors can be stretched accordingly. Spend.

Door hinge: It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, copper bearing hinges are mostly used. Because of its beautiful and bright style, moderate price, and equipped with screws.

Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible, and it is mostly used on heavy-duty doors or special steel frame steel doors.

Inclined release hinge: This kind of hinge makes use of the inclined plane of the hinge and the weight of the door leaf to automatically close the door. It is mainly suitable for lighter wooden doors or half-section doors such as toilets.

Cold storage door hinge: the surface is baked, the large size is made of steel plate, and the small size is made of cast iron. It is used for cold storage doors or heavy insulation doors.

Fan-shaped hinge: The thickness of the two sheets of the fan-shaped hinge is about half thinner than that of ordinary hinges, and it is suitable for various doors and windows that need to be rotated to open and close.

Silent hinge: also known as nylon washer hinge, when the door and window are opened and closed, the hinge is silent, and it is mainly used on the doors and windows of public buildings.

Single-flag hinge: The hinge is made of stainless steel, which is rust-resistant and wear-resistant, and easy to disassemble. It is mostly used on double-layer windows.

Window hinge: when installing, the two leaf plates with the mandrel should be installed on both sides of the window frame, and the two leaf plates without the mandrel should be installed on both sides of the window sash. One of the negative plates without the mandrel with a groove must be installed on the The grooved side of the window sash is convenient for loading and unloading of the window sash. It is used on the movable windows of factories, warehouses, houses, public buildings, etc.

Multifunctional hinge: when the opening angle is less than 75, it has the function of automatic closing. When it is at an angle of 75-90, it will be stable by itself, and if it is greater than 95, it will be automatically positioned. This hinge can be installed on the door instead of an ordinary hinge use on.

Anti-theft hinge: for ordinary hinges, when the shaft is pulled out, the door leaf can be removed. Anti-theft hinges can prevent the door leaf from being removed through the self-locking effect of the pins and pin holes on the two leaves of the hinge. It plays an anti-theft role and is suitable for residential doors.

Spring hinge: It can make the door leaf close automatically after opening. The single spring hinge can only be opened in one direction, and the double spring hinge can be opened in both directions. It is mainly used on the gate of public buildings.

Biaxial hinge: There are two kinds of biaxial hinges, left and right, which can make the door leaf open, close and disassemble freely. It is suitable for general door and window leaves.

From the above, we can know that there are many types of hinges, and the classification standards are also different, including starting from the purpose and appearance, or starting from the place and field of use, the types and names of hinges corresponding to different classification standards will also have different types. The difference, such as common door hinges, as the name implies, is used on some large doors to help open and close the hinges, that is, the so-called door hinges, and different classifications of hinges can be further detailed according to size and size. We should understand the parameters in this aspect when we study and refer to, and compare and get suitable and reliable suggestions and solutions.

Hinge Type Encyclopedia

Pipe hinges, door hinges, common hinges, other hinges.


1. The pipe hinge also has a name called a spring hinge. When the door and window are opened, it can fix an angle to prevent them from being blown around by the wind. The pipe hinge is used most on cabinet doors and wardrobe doors. It can adjust the opening angle of the door, usually 90 degrees, 127 degrees, 144 degrees and 165 degrees, etc.

2. This is a hinge specially used at the gate, because the door body of the gate is usually heavy, and in order to enhance the anti-theft safety, the material and specification requirements of the gate hinge are relatively high. The style of the gate hinge has ordinary two-fold There are two kinds of type and upper and lower bearing type. The upper and lower bearing type is more solid, so this style is usually used, and copper is mostly used.

3. This kind of hinge is generally made of iron, copper and stainless steel, and is used on cabinet doors, wardrobe doors, interior doors, and casement windows. Ordinary hinges do not have springs installed, and the doors and windows that install it need to be installed with touch beads Secure open doors and windows that are otherwise blown by the wind.

4. These are some hinges used on specific products, such as glass hinges, flap hinges and countertop hinges, and their specific uses can be seen from the names.

Villa Master provides you with local housing policies, housing drawings, and villa design drawings;

Villa appearance rendering service, thousands of popular drawings for you to choose: https://www.bieshu.com?bdfc

What is the difference between the full cover hinge and the half cover and side cover hinge? What are the hinges?

What are the differences and differences between full-cover hinges, half-cover hinges, and side-opening hinges? What are the types of hinges? What I recommend for you today is the knowledge of these aspects. From this, you can learn, first of all, It can be seen from their structural design that the so-called full cover may be more suitable for some special places, while other hinges are not the same. Another aspect and can also be classified according to the material, which can be classified according to the size and size. The detailed division includes some aluminum alloy steel materials, which are waterproof, moisture-proof and corrosion-resistant, and have a longer service life. There may also be other plastic hinges. They are relatively more cost-effective, and you can learn about them through the following.

the
1. What is the difference between full cover hinges and half cover and side cover hinges?

There are three types of door hinges: 45, 180, and 270. The angle indicates the inner angle after the cabinet is opened.

The full cover, half cover, and inlay of the hinge are determined according to the side panel of the cabinet, and the thickness of the side panel is generally 16-18MM.

Full cover: The door completely covers the side panel of the cabinet, and there is a gap between the two so that the door can be opened safely. Straight arm (0 mm) full cover door Straight arm (0 mm)

Half cover: In this case, two doors share a side panel. There is a minimum total gap required between them. The distance covered by each door is reduced accordingly, requiring the use of door hinges with curved arms. Middle curved (9.5mm) half cover door curved (9.5mm)

Responding door: In this case the door is inside the cabinet, next to the side panel of the cabinet. It also needs a clearance so that the door can be opened safely. Requires a hinge with a very curved hinge arm. Daqu (16 mm) semi-recessed Daqu (16mm)

the
the
2. Types of hinges

Ordinary hinges: used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After the hinges are installed, various touch beads must be installed. , otherwise the wind will blow the door panel.

Pipe hinge: also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height of the plate up and down, left and right , Thickness. One of its characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127 degrees, 144 degrees, 165 degrees, etc. have corresponding hinges to match, so that various cabinet doors can be stretched accordingly. Spend.

Door hinge: It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, copper bearing hinges are mostly used. Because of its beautiful and bright style, moderate price, and equipped with screws.

Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible, and it is mostly used on heavy-duty doors or special steel frame steel doors.

Inclined release hinge: This kind of hinge makes use of the inclined plane of the hinge and the weight of the door leaf to automatically close the door. It is mainly suitable for lighter wooden doors or half-section doors such as toilets.

The above recommendation is about the comparison between various hinges and the evaluation of the types. From this, we can know that the common hinges include full cover hinges, half cover hinges and side cover hinges. Three There are certain differences in their respective designs. In addition, suitable and reasonable hinges may be waterproof and moisture-proof stainless steel frame materials, or plastic materials. The corresponding cost performance and advantages are not the same. Suitable places There are also big differences. We should combine our actual needs and our respective budgets for reference, so as to achieve satisfactory results and ultimate goals.

What are the specifications of the hinge

Types of hinges Ordinary hinge: One side of the hinge is fixed on the frame, the other side is fixed on the fan, and can be turned and opened. It is suitable for wooden doors, windows and general wooden furniture. Light hinge: The hinge plate is thinner and narrower than ordinary hinges, and is mainly suitable for light wooden doors and windows and general wooden furniture. Core-pulling hinge: The hinge axis (pin) can be pulled out. After pulling out, the door and window leaves can be removed for easy scrubbing. It is mainly used for wooden doors and windows that need to be disassembled frequently. Square hinge: The hinge plate is wider and thicker than ordinary hinges. It is mainly used for doors, windows or furniture with larger weight and size. H-type hinge: It is a kind of core-pulling hinge, in which a loose leaf plate can be removed. It is mainly used for wooden doors or screen doors that need to be disassembled frequently. T-hinge: suitable for wider doors, such as factories, warehouse doors, etc. Fan-shaped hinge: the stacked thickness of the two leaves of the fan-shaped hinge is about half thinner than that of the general hinge, and it is suitable for various doors and windows that need to be rotated to open and close. Silent hinge: also known as nylon washer hinge, when the door and window are opened and closed, the hinge is silent, mainly used on the doors and windows of public buildings. Single-flag hinge: The hinge is made of stainless steel, which is rust-resistant and wear-resistant, and easy to disassemble. It is mostly used on double-layer windows. Window hinge: when installing, the two leaf plates with the mandrel should be installed on both sides of the window frame, and the two leaf plates without the mandrel should be installed on both sides of the window sash. One of the negative plates without the mandrel with a groove must be installed on the The grooved side of the window sash is convenient for loading and unloading of the window sash. It is used on the movable windows of factories, warehouses, houses, public buildings, etc. Multifunctional hinge: when the opening angle is less than 75, it has the function of automatic closing. When it is at an angle of 75-90, it will be stable by itself, and if it is greater than 95, it will be automatically positioned. This hinge can be installed on the door instead of the ordinary hinge use on. Anti-theft hinge: for ordinary hinges, when the shaft is pulled out, the door leaf can be removed. Anti-theft hinges can prevent the door leaf from being removed through the self-locking effect of the pins and pin holes on the two leaves of the hinge. It plays an anti-theft role and is suitable for residential doors. Spring hinge: It can make the door leaf close automatically after opening. The single spring hinge can only be opened in one direction, and the double spring hinge can be opened in both directions. It is mainly used on the gate of public buildings. Biaxial hinge: There are two kinds of biaxial hinges, left and right, which can make the door leaf open, close and disassemble freely. It is suitable for general door and window leaves. Screen door spring hinge: It can automatically close the door leaf after opening, and it can only be opened in one direction. The pin of the hinge can be pulled out to adjust and replace the spring. It is mostly used on solid-web steel structure screen doors. Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible. It is mostly used on heavy-duty doors or special steel-framed steel doors. Inclined release hinge: This hinge uses the weight of the inclined plane of the hinge and the door leaf to automatically close the door. It is mainly suitable for lighter wooden doors or half-section doors such as toilets. Cold storage door hinge: the surface is baked, the large size is made of steel plate, and the small size is made of cast iron. It is used for cold storage doors or heavy insulation doors.

How to install the cross hinge What are the types of hinges

When it comes to hinges, everyone should not know very well. A hinge is the metal material at the joint of doors and windows when installing doors and windows. There are many types of hinges, which are mainly classified according to the side of doors and windows. Everyone is choosing a hinge When making a page, you may not know which hinge to choose because there are too many types. In recent years, the cross lotus leaf is particularly popular. The following editor will introduce the specific information and types of the cross hinge in detail for your convenience. Choose the right cross hinge to install doors and windows!

the
Installation of the cross hingepreparation before the installation of the hinge

Determine whether the height, width, and thickness of the hinge match the wooden door. A hinge that does not match the height, width, and thickness may cause the hinge to fail to meet the load requirements and affect the use of the wooden door. The installation of the hinge requires supporting screws and other fastening accessories. Check Whether the accessories are matched and the quantity is complete.

the
Installation of cross hinges - determine the number and height of hinges

Quantity: The number of hinges is determined according to the base material of the door. Usually, only two hinges are enough for the installation of a paint-free door or a lighter door such as PVC; solid wood composite doors, solid wood doors, etc. are relatively For heavy doors, it is more suitable to install three hinges, which can also bear the weight of the wooden door and avoid deformation and damage after a long time of use. It is more appropriate to install the third hinge 30 cm below the installation position of the upper hinge.

Height: Pipe hinges (both zinc alloy and galvanized iron) have spring devices, which are mainly used for the connection of furniture door panels. 1/3 from the upper and lower corners; the installation positions of ordinary hinges are respectively 1/4 from the upper and lower corners of the door to ensure uniform force.

the
Installation of the cross hinge - installation of the hinge

Grooving: Groove on the side where the hinge is determined to be installed. The depth of the groove should be consistent with the thick soil of the single leaf. The surface of the door edge (door casing) is flush.

Fasten the hinges: Use matching screws to fix the hinges. The screws should be kept perpendicular to the door cover and the surface of the door. If the screws are inclined, there may be extrusion between the hinges when the door is closed, which will affect the service life of the door.

the
Types of hinges

Ordinary hinge: one side of the hinge is fixed on the frame, and the other side is fixed on the leaf, which can be turned and opened, and is suitable for wooden doors, windows and general wooden furniture.

Light hinge: The hinge plate is thinner and narrower than ordinary hinges, and is mainly suitable for light wooden doors and windows and general wooden furniture.

Core-pulling hinge: The hinge shaft (pin) can be pulled out. After pulling out, the door and window leaves can be removed for easy scrubbing. It is mainly used for wooden doors and windows that need to be disassembled frequently.

Square hinge: The hinge plate is wider and thicker than ordinary hinges. It is mainly used for doors, windows or furniture with larger weight and size.

H-type hinge: It is a kind of core-pulling hinge, in which a loose leaf plate can be removed. It is mainly used for wooden doors or screen doors that need to be disassembled frequently.

T-shaped hinge: suitable for wider door leaf, such as factory, warehouse door, etc.

Screen door spring hinge: It can make the door leaf automatically close after opening, and can only be opened in one direction. The pin of the hinge can be pulled out to adjust and replace the spring. It is mostly used on solid-web steel structure screen doors.

Bearing hinge (copper): Each leaf shaft of the hinge is equipped with a one-way thrust ball bearing. The door switch is light and flexible, and it is mostly used on heavy-duty doors or special steel frame steel doors.

the
How to use the hingethe installation and use method of the invisible door hinge

Align the raised alignment line on the back of the hinge with the door leaf and the door frame and draw the slotting line. When slotting, pay attention to the subtle changes in the slotting depth. It should be designed according to the slope shape of the blade thickness. When slotting, it should be deep inside and outside Shallow (closer to the axis) slope shape, the hinge blade after installation should not protrude from the plane of the door leaf or the plane of the door frame, but the groove should not be too deep, and the surface of the hinge and the door should be kept on the same level as possible.

First fix the upper hinge on the door leaf and then fix the lower hinge on the door frame. When installing, make the hinge open at a position above 90 degrees (the hinge will automatically close when it is less than 80-90 degrees). Check the hinge after installation. , Open and close the door leaf several times to see if it moves smoothly. To open the hinge function, use a Phillips screwdriver to remove the start screw, and the invisible door hinge starts to work. If you feel that the speed and strength of the hinge are not appropriate, you can adjust it through the speed regulating screw.

The above is the specific situation of the cross hinge introduced by the editor. I believe that after reading it, you should have a certain understanding of the cross hinge. When you choose a cross hinge, you must choose some good quality cross hinges. , if the quality is not good, the doors and windows will fall off, causing some unnecessary troubles and costing some maintenance costs. Therefore, when choosing, try to choose a cross hinge with good quality. I hope that the editor's suggestions can help you choose to the appropriate cross hinge for installing doors and windows!

What are the types of hinges How to choose hinges

Hinges, commonly known as hinges, are commonly used in cabinet doors, windows, doors, etc. Most of the doors and windows of modern buildings use metal hinges. Hinges can be divided into ordinary hinges, pipe hinges, door hinges, etc.

Hinges are also a must-have item in home decoration, so

Spread a hinge horizontally, the hinge does not move, nor does it fall off all at once, but slides down slowly, such a hinge is neither strenuous to close, nor will the door hit the door frame all at once , is a good hinge.

Good hinges include brass and stainless steel. Generally, the yellower the brass hinges, the better, which indicates that the copper content is high. The poor hinges will cut corners, and the specifications and thickness are not up to the standard. The thickness of the good hinges At about 3 mm, the difference page

It is relatively thin. You should choose a hinge with good sealing performance. When purchasing, you can feel its flexibility and convenience by opening and closing and pulling it several times.

(1) Before installation, check whether the hinge matches the door and window frames and leaves.

(2) Check whether the hinge groove matches the height, width and thickness of the hinge.

(3) It should be checked whether the hinge and the screws and fasteners connected to it are matched.

(4) The connection method of the hinge should match the material of the frame and leaf, such as the hinge used for the steel frame wooden door, the side connected to the steel frame is welded, and the side connected to the wooden door leaf is fixed with wood screws.

(5) When the two leaf plates of the hinge are asymmetrical, it should be identified which leaf plate should be connected to the fan, which leaf plate should be connected to the door and window frame, and the side connected to the three sections of the shaft should be connected to the frame Fixed, the side connected to the two sections of the shaft should be fixed to the frame.

(6) When installing, it should be ensured that the shafts of the hinges on the same leaf are on the same vertical line, so as to prevent the door and window leaves from springing up.

Collected for you above

How to choose and install hinges

, I hope it will be helpful to you. If you want to know more about hinge hardware, you can log in to X Group Home Network

Hinge Encyclopedia brings you the types of hinges

When you decorate a room, you need to use a lot of decoration materials, and you also need a lot of furniture to decorate the whole room, so that the room looks very beautiful. When you install doors and windows, you need to use a kind of object called a hinge. The lotus leaf is placed on the door and window The installation is very important, because the connection between the door and the door needs to be done with a hinge. There are many types of lotus leaves. When you choose, you may not know which one to choose because there are too many types. The following editor is for Let us introduce the types of hinges in detail!

What are the types of hinges?

List of Hinge TypesOrdinary Hinge

It is used for cabinet doors, windows, doors, etc. The materials are iron, copper and stainless steel. The disadvantage of ordinary hinges is that they do not have the function of spring hinges. After installing the hinges, various bumpers must be installed, otherwise the wind will Blow the door.

the
List of Hinge TypesPipe Hinges

It is also called spring hinge. It is mainly used for the connection of furniture door panels. It generally requires a plate thickness of 16-20 mm. The material is galvanized iron and zinc alloy. The spring hinge is equipped with an adjusting screw, which can adjust the height and thickness of the plate up and down, left and right. It One of the characteristics is that it can match the opening angle of the cabinet door according to the space. In addition to the general 90-degree angle, 127-degree, 144-degree, 165-degree, etc. have corresponding hinges to match, so that various cabinet doors have corresponding extensions.

the
List of Hinge Types - Door Hinge

It is divided into ordinary type and bearing type. The ordinary type has been mentioned before. The bearing type can be divided into copper and stainless steel in terms of material. From the current consumption situation, more copper bearing hinges are used because of their beautiful style. , bright, affordable, and equipped with screws.

the
Hinge specification and size:

Length*Width:

2 inches*1.5-1.8 inches

2.5 inches*1.7 inches

3 inches*2 inches

4 inches * 3 inches

5 inches*3-3.5 inches

6 inches*3.5-4

Note: inch means inch, 1 inch=25.4mm

the
Hinge installation method

The installation of the hinge is very simple, but at the same time, it is also necessary to pay attention to the differences in the style, type, and performance of the mother and child hinges. There are also certain differences in the installation. The built-in mother and child hinge is installed. It is necessary to leave a certain gap so that the door can be opened safely and flexibly. The full cover type mother hinge is installed, and the door is completely covered on the surface of the side panel of the cabinet, so it is necessary to pay attention to the size of the gap between the two. The half cover type mother hinge When installing two doors sharing the same side panel, there is a required small gap between the two, and the coverage distance of each door must be reduced accordingly.

I believe that after reading the introduction above, you should know what types of hinges are there? There are many types of lotus leaves. When choosing hinges, you must choose according to the type of your doors and windows. After installing the hinges, if you When there are some quality problems when using doors and windows, or you need to replace the doors and windows, you can remove the hinges and replace them with new doors and windows, which greatly saves the cost of maintenance and replacement. I hope that the editors suggestions can help you choose Appropriate hinges can help you better repair doors and windows.

What are the types of hinge hinges and how to choose

Hinge hinges are divided into ordinary hinges, light hinges, and pipe hinges.

When purchasing a hinge, you should choose according to the environment and material characteristics. When purchasing, you can also weigh the weight of similar products of different brands. The product with thick quality is better; the key of the hinge is to play the role of a switch. Its outer spring And the inner spring, as well as the rivet assembly are very important and cannot be ignored.

The Types of Furniture Hinges1. Detachable Type and Fixed Type:Hinges can be classified into detachable type and fixed type based on their base type. Detachable hinges can be easily removed, making it convenient to disassemble or replace furniture parts. Fixed hinges, on the other hand, are permanently attached to the furniture.2. Slide-In Type and Snap-In Type:The arm body of hinges can be categorized into slide-in type and snap-in type. Slide-in hinges have arms that slide into the base, while snap-in hinges have arms that snap into place. Both types provide secure and stable support for doors or panels.3. Full Cover, Half Cover, and Built-In Position:Hinges are also classified based on the cover position of the door panel. Full cover hinges completely cover the side panels of the furniture, providing a seamless appearance. Half cover hinges partially cover the side panels, leaving a small gap for smooth door opening. Built-in hinges hide inside the furniture, with the doors and side panels parallel to each other.4. One-Stage Force Hinge, Two-Stage Force Hinge, and Hydraulic Buffer Hinge:Hinges can be categorized according to their development stage. One-stage force hinges provide a consistent force throughout the opening and closing motion. Two-stage force hinges have different force levels for the initial opening and final closing. Hydraulic buffer hinges contain internal mechanisms that slow down and dampen the closing motion, providing a soft and silent closing experience.5. Opening Angle:Hinges can differ based on their opening angle. The standard opening angle for hinges is around 95-110 degrees, but there are also special angles available, such as 45 degrees, 135 degrees, and 175 degrees. The opening angle of the hinge should be chosen based on the specific requirements of the furniture.6. Types of Hinges:There are various types of hinges available, including ordinary one-stage and two-stage force hinges, short arm hinges, 26-cup miniature hinges, marble hinges, aluminum frame door hinges, special angle hinges, glass hinges, rebound hinges, American hinges, damping hinges, and more. Each type of hinge is designed for specific furniture applications and offers different features and functions.

Abstract: This research focuses on studying the flexibility matrix of straight beam rounded flexure hinges. The analytical calculation method for in-plane deformation of the hinge is derived based on the cantilever beam theory. The closed-loop analytical model for the flexibility matrix is established, and a simplified calculation formula for the flexibility matrix is provided when considering the corner radius and hinge thickness. Additionally, a finite element model of the hinge is developed to verify the accuracy of the analytical model. The relative error between the analytical and simulation values of the flexibility matrix parameters is analyzed for different hinge structure parameters. The results demonstrate that the analytical model is accurate, and the relative errors can be controlled within acceptable limits. Flexible hinges are widely used in precision devices due to their advantages of high motion resolution, no friction, and simple manufacturing process. These hinges rely on their own elastic deformation to transmit or convert motion, force, or energy, eliminating the need for rigid components. The key parameters of a flexible hinge directly affect its dynamic characteristics and end positioning accuracy. Previous research has focused on different types of flexible hinges, but limited studies have been conducted on straight beam rounded flexure hinges. This paper aims to fill this research gap by studying the flexibility matrix of such hinges.1. Flexibility matrix of straight beam rounded flexible hinges:The straight beam rounded flexible hinge is a sheet structure with rounded corners to avoid stress concentration. The hinge's geometric parameters include height, length, thickness, and fillet radius. A closed-loop analytical model for the flexibility matrix of the hinge is established based on the derived analytical calculation method for in-plane deformation. The flexibility matrix parameters are analyzed for different hinge structure parameters, and the relative error between the analytical and simulation values is calculated.2. Finite element verification of the flexibility matrix:To validate the accuracy of the analytical model, a finite element model of the hinge is created using UGNX NASTRAN software. The simulation results of the hinge loaded with unit force/moment are compared with the analytical values. The relative error between the analytical and simulation values of the flexibility matrix parameters is analyzed for different ratios of hinge length to thickness (l/t) and corner radius to thickness (r/t).2.1 Effect of l/t on flexibility matrix parameters:The relative error between the analytical and simulation values of the flexibility matrix parameters is found to be within 5.5% when the ratio l/t is greater than or equal to 4. For ratios less than 4, the relative error increases significantly due to the limitations of the slender beam assumption. Therefore, the closed-loop analytical model is suitable for hinges with larger l/t ratios.2.2 Effect of r/t on flexibility matrix parameters:The relative error between the analytical and simulation values of the flexibility matrix parameters increases with the increase in the ratio r/t. For ratios between 0.1 and 0.5, the relative error can be controlled within 9%. For ratios between 0.2 and 0.3, the relative error can be controlled within 6.5%.2.3 Effect of r/t on simplified flexibility matrix parameters:Simplified analytical formulas for the flexibility matrix parameters are provided considering the ratio r/t. The relative error between the simplified analytical values and the simulation values increases with an increase in the ratio r/t. For ratios between 0.3 and 0.2, the relative error can be controlled within 9% and 7%, respectively.The developed closed-loop analytical model of the flexibility matrix for straight beam rounded flexure hinges provides a theoretical basis for the design and optimization of flexible hinges and mechanisms. The accuracy of the model is validated through finite element simulations, and the relative errors are within acceptable limits for different hinge structure parameters. This research contributes to the understanding and application of straight beam rounded flexure hinges in various precision devices.