How to install wardrobe drawer slide rails How to install drawer slide rails




The first step in the installation of drawer slides: understand the composition of drawer slides

1. The smallest part of the drawer slide rail - the movable rail and the inner rail

2. The middle part of the drawer slide rail - middle rail

3. The end part of the drawer slide rail - the fixed rail is the outer rail

Drawer slide installation step two: remove all inner rails

Before installing the drawer slide rails, it is necessary to disassemble the inner rails of all the drawer slide rails (ps: the outer rails and the middle rails do not need to be disassembled directly). The disassembly method refers to pressing the inner circle of the circlip and gently pulling the inner rails of the drawer. Buckle the circlip toward the body, and then pull out the inner rail, pay attention to remove the inner rail and be careful not to deform the guide rail.

The third step of the drawer slide installation: install the main body of the drawer slide

Install the main body of the drawer slide rail on the side of the cabinet body. Generally, the panel furniture cabinet body will have ready-made holes for easy installation. Install the main body of the drawer slide rail side panels, it is best to install them before starting to assemble the furniture).

The fourth step of the drawer slide installation: install the inner rail of the drawer slide

Then install the inner rail of the drawer slide rail on the outside of the drawer with an electric screw drill. Note that there are spare holes for adjusting the front and rear positions of the drawer on the inner rail of the drawer. The front and rear positions of the drawer can be adjusted through these holes in the installation position.

The fifth step of the drawer slide rail installation: connect the drawer rails to realize the drawer installation

The last step is to embed the drawer into the cabinet body, press the snap springs on both sides of the inner rail of the drawer slide rail with your fingers, and then align the main body of the slide rail and slide it into the cabinet body in parallel.


How to install drawer slide rails, drawer slide rail installation steps and methods

Drawer slide rail installation steps:

1. First fix the five boards of the assembled drawer, screw on the screws, the drawer panel has a card slot, and there are two small holes in the middle for installing the handle;

2. To install the drawer slide rails, you first need to disassemble the rails. The narrow ones are installed on the drawer side panels, and the wide ones are installed on the cabinet body. To distinguish before and after;

3. Install the cabinet body. Screw the white plastic hole on the side panel of the cabinet body first, and then install the wide track removed from above. One slide rail is fixed with two small screws one at a time. Both sides of the body must be installed and fixed.

Precautions for installing drawer slide rails:

1. The first is the choice of size. Generally speaking, the length of the slide rail of the drawer should be the same as the length of the drawer drawer. If the slide rail is too short, the drawer cannot reach the maximum opening and closing. If it is too long, it will cause failure. Install.

2. For the drawer slides, the installation is relatively simple. The key is how to dismantle them. In some pictures of how to disassemble the drawer slides, there are more detailed dismantling steps. Through these steps, it can be dismantled very well. , so if it is time to install, then you can reverse the thinking and restore it step by step from the dismantling steps, then you will know how to install the drawer slides.

How to install the keyboard drawer slide rail

Proceed as follows:

1. Move the small plastic sheet (usually black) in the middle of the rail to one side to separate the rail into two parts.

2. Put the part without balls (with small plastic sheet) on the drawer with wood screws (note the direction);

3. Put the part with the ball (with the rail) on the table with wood screws (note the direction);

4. Move the small plastic sheet (usually black) in the middle of the drawer rail to one side and push the drawer in.


How to install the drawer rails

Disassembly method:

Open the drawer to the end and find the thin black dial at the junction of the two slide rails. It is the pointed plastic in the picture. If the position is higher, push down. Press, pull the guide rail back and it will be disassembled.

How to install drawer rails

1: Speaking of the installation method of the drawer guide rail, the length of the drawer guide rail must be the same as the length of the drawer, that is, match. If the length matches, it generally shows that the drawer

The height dimension is measured accurately, and then the measured dimension is drawn on the corresponding wooden board through the ink line.

2: After step 1 is ready, it is necessary to install it. According to the several screw holes given by the drawer guide rail, select the corresponding screw to fix it. When fixing the screw, be sure

Both sides must be fixed, and the wooden boards on both sides of the drawer must be fixed. After fixing, put the drawer into the guide rail and drag it to test whether the installation is successful.

The advantages of slide rails in furniture are numerous. Firstly, slide rails provide stability and load-bearing capacity to the furniture. They can bear, fix, and guide the mobile device or equipment, reducing friction and ensuring smooth sliding. Slide rails are especially important for drawers, as they contribute to the overall use effect and longevity of the furniture.
One of the advantages of slide rails is their use of brand-new technology to adapt to the closing speed of the drawer. With the use of hydraulic buffer technology, the drawer closes slowly on its own, reducing impact force and creating a comfortable closing effect.
When it comes to the classification of slide rails, there are two main types: steel ball slide rails and gear-type slide rails. Steel ball slide rails are made of two or three metal sections and offer smooth push and pull, with a large bearing capacity. They can also have the function of cushioning closing or rebounding to open. On the other hand, gear-type slide rails (such as hidden slide rails and horse-riding slide rails) use a gear structure to ensure smooth and synchronous sliding. These slide rails are often found in middle and high-end furniture and provide the function of buffer closing or rebound opening.
The slide rail is composed of a base, a slider, and a spring. The base is fixed on the rear end of the slide rail seat, with a guide groove and a positioning part. The slider slides in the guide chute, aided by the pull of the spring, which provides a restoring force to bounce back to the rear end of the base. The base also has a buffer sheet to elastically stop the sliding plate.
When purchasing slide rails, there are a few tips to keep in mind. First, check if the slide rail feels loose, rattles, or flips when pressed firmly. The sliding motion should be quiet and silent, with no harsh feelings or noise. The soft and silent feeling of the slide rail adds warmth to the home. It is also important to choose slide rail products produced using advanced slide rail production technology, as they offer exquisite workmanship and durable hydraulic cylinders.
When it comes to wardrobe slide rails, the choice of material is crucial. Plastic, fiberglass, and metal pulleys are common options. Plastic pulleys are hard but can become stiff with prolonged use. Fiberglass pulleys are wear-resistant and provide smooth sliding. Metal pulleys are strong but may produce harsh noises when pulled against the rails. Wardrobe slide rails are typically made of aluminum alloy, brushed stainless steel, or cold-rolled steel. The quality of the rails depends on the thickness of the material, with thicknesses greater than 1.2mm being desirable.
The style of the slide rail also affects its performance. Convex groove slide rails have a dust-proof effect and are aesthetically pleasing but can be challenging to repair if broken. Groove slide rails, while easier to clean, may lead to derailment. The choice between convex grooves and grooves depends on the specific conditions of the wardrobe.
In terms of sliding door guide rails for shower rooms, maintenance and repair may be necessary over time. If the sliding door becomes stuck or derails, there are a few steps to follow. First, check for any foreign matter stuck in the pulley or guide rail and remove it. If there is no foreign matter, lubricating the pulley and track may solve the issue. If the problem persists, the pulley may need tightening or replacement.
Overall, slide rails offer numerous advantages, including stability, load-bearing capacity, smooth sliding, and adjustable closing speed. They are an essential component of furniture, providing functionality and improving the user experience.

Expanding on the "How to Install Drawer Slide Rail" instructions, there are a few additional details and tips to ensure a smooth installation process. These steps will ensure that the drawers function properly and are aligned correctly. Here is an expanded version of the article:
How to Install Drawer Slide Rail:
Step 1: Gather the necessary tools and materials. You will need a Phillips screwdriver and a pair of 14-inch Orton drawer slides.
Step 2: Understand the different parts of the drawer slide rail. The three-section drawer slides consist of an outer rail, middle rail, and inner rail. Take note that the middle and outer rails are not removable, but the inner rail can be detached.
Step 3: Begin by removing the inner rail from the main body of the drawer slide rail. This can be done by locating the spring buckle at the back of the slide rail and disassembling it.
Step 4: Start the installation by attaching the outer and middle rail parts of the split slideway to both sides of the drawer box. If it is pre-finished furniture, there may already be pre-drilled holes for easy installation. However, if you are installing in custom-made furniture, you will need to drill the holes yourself.
Step 5: It is recommended to assemble the drawer as a whole before installing the slide rail. The track will have two sets of holes for adjusting the up-down and front-back distance of the drawer. Ensure that both the left and right slide rails are at the same horizontal position and aligned properly.
Step 6: Install the inner rail by fixing it to the measured position on the side panel of the drawer. Use screws to secure it in place.
Step 7: Tighten the screws in the corresponding holes on both sides, making sure that the inner rail is fixed to the correct length of the drawer cabinet.
Step 8: Repeat the same process on the other side, ensuring that the inner rails on both sides are horizontal and parallel to each other.
Step 9: Pay attention to the alignment of the middle and outer rails during the previous steps, as this can affect the smooth movement of the drawer. If there are any issues with the casing not being able to move forward, check the position of the outer rail or adjust the inner rail to match the position of the outer rail.
Step 10: After the installation is complete, test the drawer by pulling it in and out. If there are any difficulties or problems, make further adjustments.
How to Install Three-Section Drawer Slide Rail:
In addition to the installation instructions above, here are additional steps for installing a three-section drawer slide rail:
Step 1: Begin by installing the sub-rail in the center on the side of the drawer.
Step 2: Measure the center line from the drawer surface to the sub-rail.
Step 3: Add 3 mm to the center line measurement (or adjust according to the desired gap) to determine the pre-installation line of the main rail. Mark this line on the side panel of the drawer.
Step 4: Install the female track, ensuring it is positioned slightly backward to avoid interference with the top surface. Insert the female track into the drawer.
Step 5: Check the gap and parallelism of the drawer to ensure it is aligned correctly.
How to Disassemble and Assemble Three-Section Drawer Guide Rail:
Sometimes, it may be necessary to disassemble and reassemble the three-section drawer guide rail. Here's how to do it:
Disassembly Steps:
1. Open the drawer and locate the second section of the guide rail. Look for a black plastic pick at the junction of the second and third guide rails.
2. Check the orientation of the pick. If it is facing up, move it down to the bottom.
3. Press both sides of the pick simultaneously and pull the drawer outward to remove it.
4. Remove the screws fixing the guide rails to the sides of the drawer. Unscrew the slots on the inside of the cabinet to remove the guide rails.
Assembling the Three-Section Drawer Guide Rail:
1. Measure and determine the size and position of the guide rail.
2. Fix the slots on both sides of the drawer and the inside of the cabinet using screws.
Remember to ensure proper alignment and spacing during installation. The drawer should slide smoothly and without difficulty. Follow these detailed steps to install, disassemble, and assemble three-section drawer slide rails.

When choosing hardware for cabinets or furniture, drawer slides will have a considerable impact on both the functionality and the appearance of the outcome. Whether it is center drawer slides or kitchen drawer slides, you should consider the various factors determining which drawer slides will be the right ones for you.

Tallsen manufactures a wide variety of drawer slides intended to accommodate these needs, in addition to limiting the range of intended applications and loads. Tallsen has a great range of drawer slides. These drawer slides can be utilized in different kinds of projects

Let's explore the essential factors when selecting drawer slides and how Tallsen's offerings align with these considerations.



Understanding Travel Distance
Understanding travel distance is critical to optimizing user experience and convenience when discussing drawer slides. The travel distance refers to how far a drawer extends when opened, and it's crucial for ensuring accessibility and practicality in everyday use.



For different types of drawer slides, customizing the travel distance can significantly impact how easily items can be reached and organized within drawers, ultimately enhancing the overall functionality of furniture and storage solutions.



By considering the specific needs of each application, such as center drawer slides, kitchen drawer slides, or cabinet drawer slides, individuals can tailor the travel distance to best suit their practical requirements, resulting in a more user-friendly and efficient living or working environment.



Understanding the travel distance helps optimize user experience and organization in various settings. e.g:





Drawer Type



Typical Travel Distance



Recommended Use





Center Drawer



3/4 extension



Office desks, dressers





Kitchen Drawer



Full extension



Kitchen cabinets





Cabinet Drawer



3/4 or full extension



Bedroom or living room cabinets







Types of Drawer Slides
When selecting suitable drawer slides for various applications, it's essential to consider the specific features and functionalities offered by different types.

● Undermount Drawer Slides
Undermount drawer slides can typically support substantial weight capacities, ranging from 75 lbs to 150 lbs, providing sturdy and reliable support for various drawer applications.


● Ball Bearing Drawer Slides
Ball-bearing drawer slides, including full-extension and half-extension variants, are known for their durability and ease of movement. These slides are well-suited for cabinet drawer slides, offering reliable support and smooth functionality for diverse storage solutions.


● Heavy Duty Drawer Slides
For applications such as drawer slides for the pantry, heavy-duty Drawer slide options are essential to accommodate substantial weight and provide sturdy support, ensuring efficient organization and reliable operation in pantry storage.



● Three-Fold Normal Ball Bearing Drawer Slides
Three-fold regular ball-bearing drawer slides offer smooth and effortless movement, providing a reliable solution for cabinet and furniture applications.



● Soft Close Drawer Slides
Soft close drawer slides feature a silent and self-closing mechanism, preventing slamming noise or damage. These slides are excellent for enhancing the user experience in various drawer applications.



● Center Mount Drawer Slides
Center mount drawer slides offer a simple yet effective solution for specific drawer configurations, making them suitable for light applications.



Understanding Drawer Slides: A Buyer's Guide
When shopping for drawer slides, it's essential to consider several key factors that will influence the performance and functionality of your cabinetry and furniture. Here are some important considerations to keep in mind:





Aspect



Key Points





Load Capacity



Varies based on the type of drawer slides, such as 75 lbs to 150 lbs for under-mount drawer slides





Extension Type



Full-extension slides offer complete access to drawer contents, while partial-extension slides may suffice for certain cabinet installations





Mounting Style



Side-mount and under-mount styles are available for cabinet drawer slides, each offering distinct benefits based on aesthetics and space availability





Material and Durability



Drawer slides constructed from materials like stainless steel or zinc-plated steel prioritize quality and longevity for daily use





Soft-Closing Mechanism



The soft-closing mechanism in kitchen drawer slides adds convenience and promotes a quieter and safer environment.









Drawer Slide Mounting Methods: A Comprehensive Overview
● Center Drawer Slides For Enhanced Functionality
Consider using center drawer slides for improved stability and smooth functionality in furniture and cabinetry designs.

● Kitchen Drawer Slides For Optimal Accessibility
Opt for kitchen drawer slides to ensure seamless accessibility and organization within kitchen cabinetry, enhancing user experience.

● Cabinet Drawer Slides For Versatile Storage Solutions
Utilize cabinet drawer slides to create versatile storage solutions, optimizing space and functionality within cabinet designs.

● Drawer Slides For Pantry: Efficient Organization
Incorporate drawer slides for pantry storage to achieve efficient organization and accessibility, maximizing the utility of pantry spaces.





Tips for Installing Drawer Slides To Maximize Travel Distance And Usability
● Precise Alignment For Center Drawer Slides
When installing center drawer slides, precision in alignment is essential. This practice directly impacts the travel distance and usability of the drawers, ensuring a smooth and extended range of motion.



● Consider Weight Distribution For Kitchen Drawer Slides
For kitchen drawer slides, it's important to consider weight distribution during installation. Properly distributing the weight of drawer contents and aligning the slides accordingly can optimize the travel distance and usability of kitchen storage spaces.



● Secure Attachment For Cabinet Drawer Slides
Ensuring a secure attachment for cabinet drawer slides is vital for reliable functionality. This practice promotes stable and consistent travel distances, enhancing the overall usability of drawers within cabinets and furniture.



● Maintenance and Inspection For Drawer Slides In Pantry
Regular maintenance and inspection are essential for preserving drawer slides' optimal travel distance and usability, especially those used in pantry applications. Periodically cleaning and inspecting the slides for any signs of wear, debris, or misalignment can prevent issues that may hinder travel distance, ensuring a consistently smooth and efficient user experience within pantries.



● Invest In Quality Drawer Slides For Enhanced Functionality
Investing in high-quality drawer slides designed for durability and smooth operation can significantly impact the travel distance and usability of the drawers, whether they are center drawer slides, kitchen drawer slides, cabinet drawer slides, or those designated explicitly for pantry use. Selecting robust and well-designed slides tailored to specific applications can result in reliable performance and extended travel, contributing to enhanced functionality in everyday use.





Sum Up
When choosing drawer slides for different purposes, such as center drawers, kitchen cabinets, or kitchen drawers, various factors like load capacity, extension type, material durability, mounting style, and soft-closing mechanism are crucial in maximizing functionality and convenience. The market offers a diverse range of products from reputable suppliers, catering to different needs and preferences, whether it's heavy-duty slides with high-weight capacities or soft-close options that enhance usability.

Considering options like full-extension slides for complete drawer access or different mounting styles like side mount or under mount, it's essential to align your choices with your specific requirements. TALLSEN, a trusted manufacturer of drawer slides, stands out for its high-quality products, exceptional service, and competitive pricing. With the popular TALLSEN Drawer Slide receiving accolades from clients worldwide, TALLSEN continues to lead the industry with excellence, quality, and customer satisfaction at the core of its offerings.